Chapter 6 Review Test

 

Which of the following is a true statement regarding VLANs?
You must have at least two VLANs defined in every Cisco switched network.
 All VLANs are configured at the fastest switch and, by default, propagate this information to all other switches.
 You should not have more than 10 switches in the same VTP domain.
 VTP is used to send VLAN information to switches in a configured VTP domain.
What are the two ways that an administrator can configure VLAN membership?
Via a DHCP server
 Statically
 Dynamically
 Via a VTP database
What size frame is possible with ISL frames?
1518
 1522
 4202
 8190
How are dynamic VLANs configured?
Statically
 By an administrator
 Via a DHCP server
 Via a VLAN Management Policy Server
Which of the following protocols is used to configure trunking on a switch? ( Choose all that apply. )
Virtual Trunk Protocol
 VLAN
 Trunk
 ISL
Which of the following is true regarding VTP? (Choose all that apply.)
VTP pruning is enabled by default on all switches.
 VTP pruning is disabled by default on all switches.
 You can only run VTP pruning on 5000 or higher switches.
 VTP pruning is configured on all switches by default if it is turned on in just one VTP server switch.
Which of the following Cisco standards encapsulates a frame and even adds a new FCS field?
ISL
 802.1q
 802.3z
 802.3u
What does setting the VTP mode to transparent accomplish?
Transparent mode will only forward messages and advertisements, not add them to their own database.
 Transparent mode will both forward messages and advertisements and add them to their own database.
 Transparent mode will not forward messages and advertisements.
 Transparent mode will make a switch dynamically secure.
VTP provides which of the following benefits to a switched network? (Choose all that apply.)
Multiple broadcast domains in VLAN 1.
 Management of all switches and routers in an internetwork.
 Consistency of VLAN configuration across all switches in the network.
 Allowing VLANs to be trunked over mixed networks, like Ethernet to ATM LANE or FDDI.
 Accurate tracking and monitoring of VLANs.
 Dynamic reporting of added VLANs to all switches.
 Plug-and-Play VLAN adding.
 Plug-and-Play configuration.
Which of the following is true regarding VTP?
All switches are a VTP server by default.
 All switches are VTP transparent by default.
 VTP is on by default with a domain name of Cisco on all Cisco switches.
 All switches are VTP clients by default.
Which of the following is true regarding trunked links?
They are configured by default on all switch ports.
 They only work with a type of Ethernet network and not Token Ring, FDDI, or ATM.
 You can set trunk links on any 10-, 100-, and 1000Mbps ports.
 You must clear the unwanted VLANs by hand.
When will a switch update its VTP database?
Every 60 seconds.
 When a switch receives an advertisement that has s higher revision number, the switch will overwrite the database
in NVRAM with the new database being advertised.
 When a switch broadcasts an advertisement that has a lower revision number, the switch will overwrite the database
in NVRAM with the new database being advertised.
 When a switch receives an advertisement that has the same revision number, the switch will overwrite the database
in NVRAM with the new database being advertised.
Which of the following is an IEEE standard for frame tagging?
ISL
 802.3z
 802.1q
 802.3u
Which of the following statements describes a trunked link?
They can carry multiple VLANs.
 Switches remove any VLAN information from the frame before it is sent to an access link device.
 Access link devices cannot communicate with devices outside their VLAN unless the packet is routed through a router.
 Trunked links are used to transport VLANs between devices and can be configured to transport all VLANs or just a few.
Which of the following is true regarding an access link?
They can carry multiple VLANs.
 Switches remove any VLAN information from the frame before it is sent to an access-link device.
 Access-link devices cannot communicate with devices outside their VLAN unless the packet is routed through a router.
 Access-links are used to transport VLANs between devices and can be configured to transport all VLANs or just a few.
Which of the following statements describes access links?
They can carry multiple VLANs.
 They are used to transport VLANs between devices and can be configured to transport all VLANs or just a few.
 They can only be used with FastEthernet or Gigabit Ethernet.
 They are only part of one VLAN and are referred to as the native VLAN of the port.
What is the IEEE method of frame tagging?
ISL
 LANE
 SAID field
 802.1q
What VTP mode does not participate in the VTP domain but will still forward VTP advertisements through the configured trunk links?
ISL
 Client
 Transparent
 Server
What is the size of an ISL header?
2 bytes
 6 bytes
 26 bytes
 1522 bytes
When is frame tagging used?
When VLANs are traversing an access link.
 When VLANs are traversing a trunked link.
 When ISL is used on an access link.
 When 802.1q is used on an access link.
Your score is out of 100